Dingo Cement

Concrete & Mortar Premix

  • Very high bond strength
  • Suitable for wet areas
  • Very high early strength
  • Ideal for domestic, light and heavy commercial applications
  • Walk on in 4 hours

Dingo Self-Levelling Cement

Dingo Self-Levelling Cement is a cement based, self-levelling underlayment. It is high strength and is designed for levelling internal and external floors. Dingo Self-Levelling Cement has properties similar to concrete and it can be feathered to a 2mm edge. Using clean water Dingo Self-Levelling Cement will reach a very fluid consistency, that will leave the surface level, smooth and hard. For thicker applications, Dingo Self-Levelling Cement can be applied in layers with each layer being no more than 25mm thick.

This product can be used in both domestic and commercial applications and can be used on floors internally and externally. Whilst this product is suitable for use in wet areas, it should not be used in areas that will be constantly under water. Dingo Self-Levelling Cement can be used prior to installing floor tiles and carpet and is able to be used with tile and contact adhesives. Allow 24 hours before applying a floor covering.

Dingo Self-Levelling Cement is not to be used as a final flooring finish.

Product Information

Coverage
20kg bag of Dingo Self Levelling Cement will yield approximately 0.01m3 and cover approximately:
6.5m2 at 2mm thickness
4.33m2 at 3mm thickness

Application
2mm to 25mm thickness

Set Time
Walk on in 4 hours

Directions For Use
• A test should be performed in all cases to ensure suitability of this product.
• Do not use when temperatures are below 5°C or above 35°C.
• Do not apply if temperatures are expected to reach these levels within 24 hours of application.
• Do not use Dingo Self-Levelling Cement in applications where the product will be constantly under water

Surface Preparation
• Surfaces must be structurally sound and clean. Ensure the surface is free of all contaminants including dirt, dust, oil, grease, latex compounds, glue, paint, gypsum-based products etc.
• Contaminated substrates must be ground back to a clean surface.
• Any large cracks and holes should be patched with a suitable concrete repair mortar before using Dingo Self-Levelling Cement.
• Construction joints in the sub-floor should be carried through the self levelling cement to avoid cracking.
• All concrete sub-floors must be fully cured and dry and have a wood float finish.
• If the sub-floor has a high moisture content or subject to rising damp, apply an epoxy moisture barrier.
• Non-porous surfaces must be primed with an epoxy moisture barrier, or acid etched, or mechanically abraded to ensure the Self-Leveling cement has a rough surface to bond to.
• It is essential to prime the surface with a suitable primer before applying Dingo Self-Levelling Cement. This will improve adhesion and greatly reduce pin holing in the finished floor.
• Where the temperature is above 28ºC, it is crucial to wet down any concrete slabs with clean water before priming. Before applying the primer, ensure the floor has no pools of water and has a low sheen appearance.

Mix Process
1. Dingo Self-Levelling Cement must be mixed using a heavy-duty electric drill and paddle attachment. This will ensure you have a smooth mix. Do not use a concrete mixer or mix by hand. These are not suitable mixing methods.
2. Add approximately 4.2L to 4.6L of clean water to a clean bucket and then slowly add the 20kg bag of Dingo Self Levelling Cement. Less water may be required for colder temperatures.
3. Mix for at least 2 minutes and continue to mix until you have a smooth, lump free consistency.
4. Mixing drill should be set to maximum 600rpm.

Note: If foaming and streakiness appear on top of the mixture, Dingo Self Levelling Cement is over-watered, and should not be placed on the substrate. More powder may be added immediately whilst mixing to achieve proper consistency.
Do not mix more material than can be used in 10 to 15 minutes.

High Stress Areas
When being used in high stress areas, (for example over heated sub floors or in wet areas) Dingo Self Levelling Cement must be used with an acrylic additive. Generally, this is 1 part acrylic additive to 2 parts water, however follow the directions on the acrylic additive packaging. Add approximately 5L of this mix to a 20kg bag.

Large Areas
Large areas requiring fills between 25 -100mm, use MaxPRO Concrete Mix or Dingo Hi Strength Concrete Mix. If using Dingo Hi Strength Concrete Mix add reinforcing steel if fill is more than 25mm. Ensure you attach the new concrete to the old concrete using pins.

Pumping
If pumping mix in an appropriate pre-pump mixer. Do not mix more material than can be used in 10-15 minutes. Mix speeds must not be too high, otherwise it will cause aeration. Clean mixers and pumps thoroughly after each batch to avoid material build up.

Application instructions 
1. Section off the work into areas no larger than 13.4m². It is essential that control joints and expansion joints are maintained. Use weather stripping or duct tape to prevent MaxPRO Concrete Resurfacer from spilling into joints.
2. Saturate the surface with water from a hose, and then remove any standing water with a long handle industrial squeegee.
3. Pour MaxPRO Concrete Resurfacer mixture from bucket on to surface.
4. Using the long handle squeegee spread the MaxPRO Concrete Resurfacer mixture across the surface. Use the squeegee to scrub the material into the surface smoothly.
5. For a slip resistant professional finish, follow within five minutes with a large push broom, making full strokes across the entire distance of the current work area without stopping. If desired, a concrete edging tool can be used within 20 minutes of pouring.
6. For thicker applications, use additional thin layers of MaxPRO Concrete Resurfacer, building up to the desired thickness, or use a trowel-applied layer after the initial squeegee application. For trowel-applied mixes, reduce the water to approximately 2.9L per 20kg bag.

Safety

Safety

  • Wear suitable protective clothing, including gloves and eye protection
  • Avoid contact with eyes and skin from wet and dry cement
  • Avoid breathing dust by wearing suitable respiratory equipment
  • Wash skin thoroughly after handling
  • For more Safety & Storage information refer to SDS sheets.